TAHOE II SENSOR is a ceiling light from Nowodvorski Lighting, symbol 10040: a plain white fitting measuring 25 x 25 cm, with a built-in motion sensor and an IP44 rating. Made in Poland.
The motion sensor — what it is actually for
The built-in detector switches the light on when it senses movement and off again once activity stops. In practice this type of fitting goes where reaching for a switch is awkward or impossible: a hallway when your hands are full, a walk-in wardrobe, a pantry, a utility room, a corridor to the bedrooms, a cellar or a garage. The side effect matters as much as the convenience — the light never gets left on all night by mistake.
An important caveat: Nowodvorski does not publish this sensor's parameters — neither the detection angle, nor the range, nor the hold time, nor the twilight threshold. They appear neither in the specification table on the manufacturer's site nor in the datasheet. If those values are critical for your application (a long corridor, or a room of unusual height), it is worth confirming them from the instruction sheet supplied with the fitting before you buy.
IP44 — but for indoors
The manufacturer's datasheet states the intended use in one word: "Interior". The IP44 rating here means resistance to splashing water from any direction, which allows the fitting in a bathroom (outside the shower zone) and in rooms with raised humidity — a utility room, kitchen or cellar. It is not, however, an outdoor fitting: it should not be mounted in the open or on an unsheltered terrace.
Two E27 sockets — and a limit that is easy to forget
The fitting takes two E27 lamps, and the manufacturer writes the power limit in a distinctive way: "2x15W only LED" — a maximum of 15 W per socket and LED technology only. That is a real restriction: a classic 60 W incandescent or a halogen will screw in without difficulty but will exceed the thermal load the closed plastic housing is built for. Two 15 W LED lamps give around 2500–3000 lm in practice, which is ample for a hallway or bathroom.
Lamps are not included — you choose them yourself. For a hallway and bathroom 3000 K is the natural choice, for a utility room or garage rather 4000 K. With a sensor fitting it is worth picking lamps with a short start-up time and a high switching-cycle rating, because the detector will turn them on and off many times a day.
Build
The construction is entirely plastic: a polycarbonate (PC) body with ABS supporting parts. White, minimal, undecorated — the fitting is meant not to draw attention. Protection class II means double insulation and no need for an earth conductor, which greatly simplifies replacing an old fitting in a building with two-core wiring.
Installation
The fitting is designed for direct mounting — screwed straight to the ceiling or wall. Note: the manufacturer does not supply a mounting kit (plugs and screws); these must be matched to the substrate. At a net weight of just 0.51 kg this is not a demanding job, but it is worth remembering when ordering.
Specification
-
Symbol: 10040 | EAN: 5903139100403
-
Collection: TAHOE II
-
Dimensions: 25 x 25 cm
-
Net weight: 0.51 kg | gross: 0.61 kg
-
Packaging: 25 x 25 x 7 cm
-
Base: E27 | Light points: 2
-
Maximum power: 2 x 15 W, LED only
-
Lamps included: no | Lamps: replaceable
-
Sensor: motion (parameters not published by the manufacturer)
-
Ingress protection: IP44 | Intended use: interior
-
Protection class: II
-
Supply: ~220–230 V / 50–60 Hz
-
Materials: PC plastic, ABS plastic
-
Colour: white | Style: modern
-
Mounting method: direct | Mounting kit: not included
-
Country of manufacture: Poland
The TAHOE family
The collection covers several versions of the same body: TAHOE, TAHOE II, TAHOE II MAT and the TAHOE II SENSOR described here. They differ in the diffuser finish and in whether a sensor is fitted, so within one flat you can put the detector version in the hallway and the plain version elsewhere while keeping a consistent look.